Simatara Build 12-12 https://www.breakingwindboats.com/apps/photos/ Simatara Build 12-12 Draw line and trim hull https://www.breakingwindboats.com/apps/photos/photo?photoID=171123361 171123361 Draw line and cut deck Do a good job here this one shows. https://www.breakingwindboats.com/apps/photos/photo?photoID=171123357 171123357 Deck Finish cut https://www.breakingwindboats.com/apps/photos/photo?photoID=171123347 171123347 Round file into corners before folding Avoid square cuts anywhere with plastic. https://www.breakingwindboats.com/apps/photos/photo?photoID=171123350 171123350 Second corner Avoid square cuts anywhere with plastic. https://www.breakingwindboats.com/apps/photos/photo?photoID=171123353 171123353 Folding is after trimming Don't try to go all the was at once. A few passes will follow the crease. It will spring back some. https://www.breakingwindboats.com/apps/photos/photo?photoID=171123410 171123410 Hull edge folded in https://www.breakingwindboats.com/apps/photos/photo?photoID=171123411 171123411 Mark center line on hull https://www.breakingwindboats.com/apps/photos/photo?photoID=171123346 171123346 Getting center line to inside https://www.breakingwindboats.com/apps/photos/photo?photoID=171123351 171123351 No turning back, cut the hole. https://www.breakingwindboats.com/apps/photos/photo?photoID=171123412 171123412 Glue 2 trunk half's together https://www.breakingwindboats.com/apps/photos/photo?photoID=171123414 171123414 Mark keel trunk on template. https://www.breakingwindboats.com/apps/photos/photo?photoID=171123363 171123363 My keel needed some work to fit into trunk https://www.breakingwindboats.com/apps/photos/photo?photoID=171123345 171123345 Dry fit the 3 together Tape holds keel and hull in correct position. https://www.breakingwindboats.com/apps/photos/photo?photoID=171123349 171123349 Trunk with glue https://www.breakingwindboats.com/apps/photos/photo?photoID=171123344 171123344 Top support Next time I'll make the trunk lower and top will be solid. https://www.breakingwindboats.com/apps/photos/photo?photoID=171123348 171123348 Bow taped ready to glue. This is an easy place to add to much glue / weight. https://www.breakingwindboats.com/apps/photos/photo?photoID=171123355 171123355 My assistant .... https://www.breakingwindboats.com/apps/photos/photo?photoID=171123354 171123354 set up to drill rudder post. Hull and deck It is up on the block to drill square to the waterline. https://www.breakingwindboats.com/apps/photos/photo?photoID=171123359 171123359 Post glued in https://www.breakingwindboats.com/apps/photos/photo?photoID=171123362 171123362 Deck and hull ready to glue together. https://www.breakingwindboats.com/apps/photos/photo?photoID=171123358 171123358 Taped in place. Start gluing MEK from the stern. https://www.breakingwindboats.com/apps/photos/photo?photoID=171123356 171123356 Gluing where the tape was. https://www.breakingwindboats.com/apps/photos/photo?photoID=171123352 171123352 Needed to pull out a spot before gluing. https://www.breakingwindboats.com/apps/photos/photo?photoID=171123360 171123360 Rod glued in keel. cut off after. https://www.breakingwindboats.com/apps/photos/photo?photoID=171123413 171123413