These are instructions on how to jailbreak your iPhone with QuickPwn. The instructions have been updated for the latest (2.2) version of the iPhone firmware.
Note: You could use this tutorial as first step to unlocking the iPhone 2G. Simply complete this tutorial to jailbreak then install BootNeuter from Cydia to complete the unlock.
Important***: Do not attempt these instructions for the 2.2 iPhone Firmware unless you don't care about a software unlock in the future. Using QuickPwn with the 2.2 iPhone Firmware could reduce your chances of being able to unlock the iPhone 3G.
Step One
Create a folder on your desktop called Pwnage
Step Two
Download QuickPwn 2.2 from here and place it in the Pwnage folder. Likewise, download the latest 2.2 firmware from below and place it in the same folder.
2.2.0 (2G): iPhone1,1_2.2_5G77_Restore.ipsw
2.2.0 (3G): iPhone1,2_2.2_5G77_Restore.ipsw
Step Three
Double click to mount the QuickPwn [QuickPwn_22.dmg] archive. Drag the QuickPwn application icon into the Pwnage folder on your desktop.
Step Four
Double click to launch QuickPwn from the Pwnage folder.
Step Five
Click OK to accept the copyright notice.
Step Six
Connect your iPhone to the computer when asked then click the OK button.
Step Seven
QuickPwn will now automatically detect the device connected!
Step Eight
QuickPwn will now automatically search for the latest firmware for this device
Step Nine
You will be asked if you would like to replace the original boot and recovery logos on your iPhone. Select Yes or No to continue.
Step Ten
QuickPwn will now begin building your custom IPSW.
Step Eleven
You will be asked to enter your administrator username and password. Do this, then click OK to continue.
Step Twelve
QuickPwn will now help you put your iPhone into DFU mode. First, turn off the device.
Next, you will be asked to hold both the Home and Power buttons for 10 seconds.
Finally, you will release the power button and continue holding down the Home button for another 10 seconds.
Step Thirteen
QuickPwn will now automatically begin sending information to your iPhone.
Step Fourteen
You will now be notified that QuickPwn is modifying your iPhone. The process will take some time and will cause the iPhone to reboot. Don't do anything until the process has completed!
Step Fifteen
Once your iPhone has rebooted it will be jailbroken and have both Cydia and Installer on the Springboard!
Note: You could use this tutorial as first step to unlocking the iPhone 2G. Simply complete this tutorial to jailbreak then install BootNeuter from Cydia to complete the unlock.
Important***: Do not attempt these instructions for the 2.2 iPhone Firmware unless you don't care about a software unlock in the future. Using QuickPwn with the 2.2 iPhone Firmware could reduce your chances of being able to unlock the iPhone 3G.
Step One
Create a folder on your desktop called Pwnage
Step Two
Download QuickPwn 2.2 from here and place it in the Pwnage folder. Likewise, download the latest 2.2 firmware from below and place it in the same folder.
2.2.0 (2G): iPhone1,1_2.2_5G77_Restore.ipsw
2.2.0 (3G): iPhone1,2_2.2_5G77_Restore.ipsw
Step Three
Double click to mount the QuickPwn [QuickPwn_22.dmg] archive. Drag the QuickPwn application icon into the Pwnage folder on your desktop.
Step Four
Double click to launch QuickPwn from the Pwnage folder.
Step Five
Click OK to accept the copyright notice.
Step Six
Connect your iPhone to the computer when asked then click the OK button.
Step Seven
QuickPwn will now automatically detect the device connected!
Step Eight
QuickPwn will now automatically search for the latest firmware for this device
Step Nine
You will be asked if you would like to replace the original boot and recovery logos on your iPhone. Select Yes or No to continue.
Step Ten
QuickPwn will now begin building your custom IPSW.
Step Eleven
You will be asked to enter your administrator username and password. Do this, then click OK to continue.
Step Twelve
QuickPwn will now help you put your iPhone into DFU mode. First, turn off the device.
Next, you will be asked to hold both the Home and Power buttons for 10 seconds.
Finally, you will release the power button and continue holding down the Home button for another 10 seconds.
Step Thirteen
QuickPwn will now automatically begin sending information to your iPhone.
Step Fourteen
You will now be notified that QuickPwn is modifying your iPhone. The process will take some time and will cause the iPhone to reboot. Don't do anything until the process has completed!
Step Fifteen
Once your iPhone has rebooted it will be jailbroken and have both Cydia and Installer on the Springboard!