Motorola V998(V3688)

Needed tools:

A set of assembly tools with five pieces (chart a show),
chart b show the use for all tools.

Item noted and explanation :

Owing to V998 series mobile was assumed with plastic buckle, no mechanical fixed bolt, so we must use professional tools showing in chart a,
Don't exert your strength hardly when topping out signal light shield with tool B, and avoid inner LED pulled off,
must point at the position of buckle when using tool D, tool E, the position for the plastic buckle of V998 series mobile are show in chart b.

.Turn on button when pressing back cover of battery, and take out back cover.

Take out battery.

Rotate antenna and put it out with tool A according to chart show.

Return tool B to orignal position for battery.

Top out signal light guide using thimble of tool B.

Pull out signal light guide with tool C.

Poke four plastic buckle of back cover with tool D or tool E.

Remove back cover.

Loosen cable socket clip before taking out the cable head of LCD.

Draw out cable with plier, be careful not to remove it bendy, and avoid breaking circuity.

Take out main PWB.

Heat up front board (button board) with fanner, so that remove front board easily.

Apart keyboard.

Take out subassembly of LCD and headphones.

Pull out cable slowly and then apart front panel.

Take out rotating axes with plier.

Use tool D or tool E to remove plastic buckle of the upper and lower cover.

Use tool D or tool E to apart four plastic buckle of the upper cover, and then take out the upper cover

Take apart the subassembly of LCD and headphones

Unsolder LCD panel's copper filmand then apart them with plier.

Heat up LCD with fanner. (Note proper temperature).

Loosen three plastic buckle of LCD.

Take out headphones.

Take out the subassembly of LCD.

The operaton is over.

Motorola L2000

Needed tools:

One A5 or T6X50mm screwdruver,
one knife sheet,
straight plier or curve plier,
one fanner.

7X7mm automatical screw.

Item noted and explanation :

Be careful to screw under "MOTOROLA" label when take apart the screw,
use conductor glue to connect LCD panel with main PWB, be careful to keep tools and desk clean and don't let conductor glue smeary.

Take out back cover of batter and then take out battery.

Heat up " MOTOROLA" label on the top of back cover with fanner then take out with knife sheet (plier) for further use.

Unscrew two bolts under "MOTOROLA" label with T6 X50mm or A5 screwdriver.

Unscrew four bolts of the middle and lower of back cover with T6 X 50mm or A5 screwdriver.

Apart back cover.

Take out main PWB.

Push off four buckles of LCD with right fore finger and take out the subassembly of LCD.

Poke the plastic frame of conductor slice in LCD subassembly.

Take out conductor frame before off loading LCD.

The operation is over..

Motorola V60

Needed tools:

One T5 and T6 screwdriver,
one plastic screwdriver,
one bend plier.

Item noted and explanation :

Dry and clear repair condition is necessary, operation platform is essential,
Motorola V60 is slap-up trine-frequency mobile phone, you ought to avoid the hard object to contact the cover, or avoid to damage the cover face and inner PCB when dismantling for the cover is refined in technics.
if it is difficult to dismantle due to the plastic, please heat with fanner.

Take out back cover of battery.

Unscrew the two fixed bolts with T6 screwdriver.

Take apart back cover with plastic screwdriver!

Apart back cover.

Apart FPC.

Takeout PCB.

Take out keypad and keypad baffle.

Apart front cover and PCB.

The operation is finished.

Motorola V66

Needed tools:

One T5, T6 screwdriver,
one plastic screwdriver,
one bend plier.

Item noted and explanation :

Dry and clear repair condition is necessary, operation platform is essential,
Motorola V66 is slap-up trine-frequency mobile phone, you ought to avoid the hard object to contact the cover, or avoid to damage the cover face and inner PCB when dismantling forthe cover is refined in technics,
if it is difficult to dismantle due to the plastic, please heat with fanner.

Rotate antenna and pull it out.

Unscrew two fixed bolts.

Take out of indication light.

Take apart the back with plastic screwdriver. b. Take out the back cover.

Take apart FPC socket.

Take out PCB.

Apart PCB and key board.

Take out the small cover.

Dismantle the three bolts in cover with T5 screwdriver.

Take out LCD face.

Apart cover and PCB.

Take out LCD board of cover.

The operation is finished

Motorola T189

Needed tools:

One T6X50mm screwdriver,
one knife sheet,
one fanner.

Take out the back cover and battery.

Unscrew the four fixed bolts in the back cover with T6X50mm screwdriver.

Heat up the MOTOROLA label on back cover with fanner, and then take it out with knife sheet.

Unscrew the two fixed bolts under the label with T6X50mm screwdriver.

Apart back cover.

Take apart vibrator socket with T6X50mm screwdriver or knife sheet.

Takeout PCB.

Loosen LCD button on PCB.

Turn out LCD IC upwards to dismantle FPC.

Loosen LCD FPC fastener to take out FPC head, then take out LCD IC.

The operation is finished.

Motorola T191

Needed tools:

One T5 screwdriver,
one plastic screwdriver,
one fanner.

Item noted and explanation :

Dry and clear repair condition is necessary, operation platform is essential,
*Motorola V191 is slap-up trine-frequency mobile phone, you ought to avoid the hard object to contact the cover when dismantling for the cover is refined in technics,
If it is difficult to dismantle due to the plastic, please heat with fanner.

Take out battery.

Take out the label on back cover.

Dismantle the two bolts under the label and the other two bolts in back cover with T5 screwdriver.

Push out the back cover button moderately.

Unscrew the two bolts under back cover button with T5 cross screwdriver.

Apart back cover with plastic screwdriver carefully.

Take out back cover

Apart PCB.

Take apart shield cover of PCB.

Dismantle the components in back cover, such as buzzer, vibrator and antenna.

The operation is finished.

Motorola A6188

Needed tools:

One T6X50mm screwdriver,
one straight plier of curving plier,
2.0X50mm straight screwdriver.

Item noted and explanation :

Note the bolt which is under the rubber on the top of back cover,
Due to A6188 LCD is assembled with keyboard together, using touch button, and don't take apart the subassembly of LCD optionally.

Press lock backle of back cover of battery, and pull out back cover of battery.

Take out the battery according to chart show.

Loosen the two bolts which are in the lower of back cover with T6 x 50mm screwdriver.

Loosen bolt which is hided in the hole with T6X 50mm screwdriver. Take out two dustproof rubber covers which are sticked on the upper of back cover with plier.

Remove the back cover.

Poke the connecting plug of headphones with plier.

Poke cable of LCD and remove it with 2.5 X 50mm straight screwdriver.

Loosen the two bolts which fix the main PWB with T6 X 50mm screwdriver.

Take out main PWB.

Take out the disassembly of LCD.

Taking apart the disassembly of upper panel according to chart show.

The operation is over.

Nokia 3210 opening manual - just see how it is simple and do it by your self.

Nokia 3210 is a cellphone that is very simple to desolder. Sometimes when we want to install for example vibramotor, we must open it. In case if you got problem with it we have prepared short instruction how to make this operation faster and without any suprise.

Needed tools:

Torx T6 screwdriver - you may buy full pack in our Store

Pointer - you may use a small screwdriver too. Full pack ot TORX an pointer may be available in our Store

How to do this:

deatach battery
remove two screw with screwdriver TORX-6 that are in bottom part of phone (one in left and second in right corner of phone)

desolder antenna with pointer (you may pull it form right of left side but be cerfull to not demage clips)

remove next two screws that were under antena and use pointer to pull up metal cover (pull it up near SIM slot). Remove it.

you may now see PCB (Printed Circuit Board) of phone

Nokia 3310

Needed tools:

One T6X50mm or A5 screwdriver,
one straight plier.

Press the battery button of lower back cover, push out the battery back cover.

Take apart battery button with your thumb pushing hardly and take out battery.

Remove front cover.

Unscrew six pieces fixed bolt of front panel with T6 X 50mm or A5 screwdriver.

Remove six pieces plastic button of front panel with plier.

Take out front panel.

Take out man PWB.

Push out shield cover.

The operation is over

Nokia 5110

Your 5110 display is demaged and you want to replace it ? Just read this...

Nokia 5110 is a cellphone that is very simpel to desolder. Desoldering is needed if you want for example replace broken display or make some repairs in phone. In case if you got problem with it we have prepared short instruction hot to make this operation faster and withtou any suprise.

Needed tools:

Torx T6 screwdriver - you may buy full pack in our Store

How to:

deatach battery (photo 2)
remove four screw with screwdriver TORX-6 that two of them are in bottom part of phone (one in left and second in right corner of phone) and rest wo near sim slot card

Photo.1 Photo.2

take off front panel by pushing clip near antenna (as shown on picture) and take off plastic over of display.

remove 2 more screws that are located near microfone.

Photo.3 Photo.4

you can now remove PCB panel with display (photo 4)

after removing PCB with display you will see main board of phone. Just remove one screw that are in the center on this PCB to take off main board from phone.

Nokia 8210

Needed tools:

One T6X50mm or A5 screwdriver,
one straight plier.

Item noted and explanation:

Take care of all parts removed.

Push the black button on top of mobile, remove front panel.

Unscrew six pieces fixed bolts of front panel with T6X50mm or A5 screwdriver.

Take out the subassembly of main PWB and front panel.

Remove plastic buckle four pieces of front panel(LCD).

Remover front panel(LCD).

Remove plastic buckle of LCD.

Remove plastic buckle of LCD

Take out LCD.

The operation is over.

Nokia 8310

Needed tools:

One T6X50mm screwdriver,
one bend plier.

Item noted and explanation :

Dry and clear repair condition is necessary, operation platform is essential,
adsorb the dismantled bolts together by means of magnet(also can use old earphone) avoiding to loss the bolts,
Nokia 8310 is slap-up trine-frequency mobile phone, you ought to avoid the hard object to contact the cover when dismantling for the cover is refined in technics.

Take out the back cover of battery.

Apart front cover and PCB.

Dismantle the six fixed bolts with T6 screwdriver.

Apart the front cover.

Apart PCB.

The operation is finished.

Nokia 8810

Nokia 8810

Needed tools:
- One T6X50mm or A5 screwdriver,
- one straight plier.
Item noted and explanation:
- Item noted and explanation,
- take care of push-switch under main PWB when taking apart main PWB and cover,
- take care of all removed parts.
- Take apart battery cover.
- Unscrew fixed bolts two pieces of back cover with T6 X 50mm or A5 screwdriver.
- Unscrew two pieces of fixed bolts of front cover with T6 x 50mm or A5 screwdriver.
- Unscrew two pieces of fixed bolts on top of front cover with T6 X 50mm or A5 screwdriver.
- Remove middle cover, take care of the antenna on tc.
- Remove main PWB, take care of small end switch.
- Take apart front cover and keyboard.
- The operation is over.

Philips 939

Needed tools:

One professional unlock plier(use SIEMENS for replacement),
one T6X50mm or A5 screwdriver,
one fanner,
one straight plier, one plastic crowbar.

Item noted and explanation:

Use plastic buckle and fixed part as fixed method, and be careful to use the professional tool,
Notice: Be careful not to damage the LCD when taking off the fixed bolt under the LCD.

Slide battery and take it out when pressing lock buckle for battery.

Unscrew four fixed bolts for back cover with T6X50mm or A5 screwdriver.

Rotate antenna and pull it out.

Apart the top plastic buckle for mobile with professional plier.

Apart plastic buckle for the middle of main body with plastic crowbar, and remove the front cover.

Unscrew two fixed bolts on the top of main board with T6 X 50mm screwdriver.

Head up LCD with fanner, notice that the temperature can't be too high, avoid breaking LCD.

Poke LCD with professional crowbar(start from the top of LCD).

Apart the end of LCD with plier.

Unscrew two fixed bolts under the LCD with T6X50mm screwdriver.

Take out main PWB.

Poke cable plug for keyboard.

Draw out cable head from inner socket of main PWB cable.

The operation is over.

Panasonic GD92

Needed tools:

One 2.0x50mm screwdriver,
one straight plier.

Item noted and explanation:

Due to Gd92 mobile is thin, be careful not to bend main PWB and LCD.

Take out battery when pressing lock buckle for battery.

Unscrew four fixed bolts for back cover with starlike 2.0 x 50mm screwdriver.

Apart six plastic buckles for front and back cover, and remove back cover.

Take out main PWB.

Poke plastic buckles of headphones subassembly.

Take out headphones subassembly.

Apart six plastic buckles of the front and back cover.

Take out main PWB.

Slide key board to right direction.

Take apart LCD.

The operation is over.

Panasonic GD90

Needed tools:

One 2.0x50mm screwdriver,
one straight plier.

Item noted and explanation:

Due to Gd90 mobile is thin, be careful not to bend main PWB and LCD.

Take out battery when pressing lock buckle for battery.

Rotate antenna and pull it out.

Unscrew four fixed bolts for back cover with starlike 2.0X50mm screwdriver.

Take apart six plastic buckles of the front and back cover.

Take out main board.

Remove four plastic buckles for front panel.

Take out front panel (show keyboard).

Take apart middle cover (shield board).

The operation is over

SAMSUNG SGH-800

Needed tools:

One C2.0x50mm cross screwdriver,
one T6X50mm or A5 cross screwdriver,
one straight plier or bend spade,
one fanner.

Item noted and explanation :

Note fixed bolt under the guarantee label.
Must keep dustproof cover both for antenna and earphone socket when taking apart.
All parts with mucilage glue such as LCD, headphone should be heated up with fanner firstly and then remove them.

Press lock buckle of battery and pull out the battery.

Rotate antenna, and pull it out.

Unscrew four fixed bolts with T6 x 50mm or A5 screwdriver.

Remove back cover according to chart show.

Pull of shield cable fo LCDr with solder.

Then separate shield cable and main PWB with plier.

Take out main PWB.

Take out the clapboard between main PWB and front panel.

Take out shield cable end between LCD and front panel with plier.

Poke cable card of LCD with plier.

Take out LCD cable.

Take out main PWB.

Top apart the axes bolt of upper and lower cover.and push out the front cover with thumb.

Separate front panel and the upper and lower cover.

Pull out LCD cable according to chart show.

Unscrew two pieces of fixed bolt of the upper and lower cover with R 2.0 X 50mm screwdriver.

Push out the upper cover according to chart show.

Take out the up per cover.

Heat up the back of display screen with fanner.

NOTE:
Temperature can't be too high . Avoiding cover distortion.

Take out headphone with plier.

Take out vibrator with plier.

Remove the LCD, and take out of the cable in the axes of lower cover.

The operation is over.

Samsung A288

SAMSUNG SGH-A288

Needed tools:

One 2.0X50mm cross screwdriver one fanner,
one straight plier plastic crowbar and knife sheet.

A288 is one of current popular top grade mobiles, be careful when taking apart and avoid breaking the delicate over and inner main PWB done to the cover is delicate ..

How to:

First:
Take out battery, then see four black cross bolts in back cover(show above) , for a new mobile one bolt covered by guarantee label, heat up the label with fanner firsthand slice if off gently and flatly for further use. Avoiding guarantee label broken when disassembling.

Later You must:

According to direction shown circumrotate and take off antenna.

Use C2.0x50mm cross screwdriver loosen the fixed screw.

Take off the lower part according the chart shown.

Take off the upper part of back cover.due to two plastic lock clip in it.exert your strength equably, the right thumb must be against the upper part.

Use plier to take off the subassembly of display screen and soft cable connecting PWB.

Use plier to take off connecting socket soft cable head between key board and main PWB.

Hold the outer connecting socket of main PWB,exert your strenght up gently.and take off main PWB.

Next:

Take out of the key board, be carefu don't bend soft cable connector avo d breaking.

Must take off plastic side key.

Take out side key touch point.

Disassembling the upper and lower cover (The subassembly of display screen) .

Pull apart un-dry glue on the cable socket which is on the upper of front panel with plier.

Take out axes bolt of the lower and upper cover with C2.OX 50mm and 02.OX 50mm.

Pull out the upper and lower ocver assembly.note that fish up cable plug from cable socket.

With fanner heat up the two holes which is under the big display screen of lower cover.

Prize up the white un-dry glue paper with knife sheet and keep for use.

Loosen two fixed screws with C2.0X50mm specification cross screwdriver.

Heat up telephone receiver of the lower cover with fanner.

Prize up the cover of headphone with crowbar(or knife sheet),be careful when you exert your strenqth,not let cover break.

Loosen two fixed screws with R2.OX50mm specification cross screwdriver.

Remove the middle plastic buckle of lower cover,
take apart the lower and upper cover.

Heat up the subassembly of display screen with fanner,
prize up vibrator, headphone, button battery and so on.

Take off the subassembly of display screen,and the work has been finished.

Samsung A100

SAMSUNG SGH-A100

Needed tools:

One T6X50mm or A5 cross screwdriver,
one C2.OX50mm cross screwdriver,
one straight plier,
one fanner.

Item noted and explanation :

Note the fixed bolt which under the guarantee I label,
must keep the dustproof cover of antenna test hole and earphone socket during the whole process, use for reassembly.

All parts with mucilage glue, such as display screen headphone, must remove after heating up with fanner during apart process.

First:

Press battery lock buckle, take out of the battery upward.

Heat up seal guarantee label or cluster code paper with fanner, get it out with knife sheet for further using.

Loosen four fixed bolts with T6x50mm screwdriver.

Rotate antenna and pull it out.

Remove plastic buckle on the middle of back cover.

Remove plastic buckle on the upper of back cover.

Poke display screen cable card, and take out the cable.

Take out main PWB.

Remove the two plastic buckle on the middle of clapboard.

Take out clapboard.

Take out side key button.

Take out front panel.

Top out the axes bolt of the upper and lower with T6 x 50mm screwdriver,
top out front panel with left thumb.

Separate the join between the upper and lower cover and front panel.

Unscrew two fixed screws of the upper and lower cover.

Push out the upper cover.

Heat up subassembly of display screen with fanner and take it out.

The operation is over.

Samsung SGH-2400

SAMSUNG SGH-2400

Needed tools:

One T6X50mm screwdriver,
one straight plier.

Item noted and explanation :

There are five pieces of fixed bolts for 2400 model, the same taking apart process with model 2488,
note the bolt which is under the antenna and upper rubber dustproof cover.

Unscrew the antenna according to the direction show.

Pull out the antenna gently according to the right direction show.
- Unscrew the four fixed bolts on back cover with T6 specification screwdriver.
- Take out the rubber dustproof cover gently through the small hole which is on the upper of back cover.
- Unscrew the fixed bolt on the upper of back cover.
- Remove back cover.
- Take out join plug of vibrator by use of plier.
- Take out connector cable plug for display screen by use of plier.
- Take out main PWB as the chart show.
NOTE:

The thumb of right hand must be against front panel.
Taking apart front board subassemlbly
- Take out telephone transmitter.
- Take out the vibrator.
- Take out headphone.
- Take out the cable of side key.
- The operation is over.
Samsung N188

SAMSUNG SGH-N188

Needed tools:
- One T6X50mm screwdriver,
- one straight plier.
Item noted and explanation :
- Note the bolt under rubber sheet, which is on the top of back cover.
- The arrowhead indicated on chart is the bolt under dustproof cover.
- Press down buckle lock of battery and take out battery.
- Anticlockwise rotate antenna and take it out according to chart show.
- Unscrew four fixed bolt with T6 screwdriver.
- Take out bolt dustproof cover, which is on top of back cover and unscrew inner bolt with T6.
- Separate the end of back cover firstly.
- Separate the top of back cover.
- Separate the back cover completely.
- Take out connecting plug for vibrator by use of plier.
- Poke connective cable of keyboard by use of plier.
- Take out main PWB.
- Take out front panel and take out telephone transmitter subassembly firstly.
- Take outside key cable for volume and then front panel,
- The operation is over.

Motorola V998(V3688)

Needed tools:

Motorola L2000

Needed tools:

Motorola V60

Needed tools:

Motorola V66

Needed tools:

Motorola T189

Needed tools:

Motorola T191

Needed tools:

Motorola A6188

Needed tools:

Nokia 3210 opening manual - just see how it is simple and do it by your self.

Needed tools:

How to do this:

Nokia 3310

Needed tools:

Your 5110 display is demaged and you want to replace it ? Just read this...

Needed tools:

How to:

Nokia 8210

Needed tools:

Nokia 8310

Needed tools:

Nokia 8810

Needed tools:

Philips 939

Needed tools:

Panasonic GD92

Needed tools:

Panasonic GD90

Needed tools:

SAMSUNG SGH-800

Needed tools:

SAMSUNG SGH-A288

Needed tools:

How to:

Take off the subassembly of display screen,and the work has been finished.

SAMSUNG SGH-A100

Needed tools:

SAMSUNG SGH-2400

Needed tools:

SAMSUNG SGH-N188

Needed tools: