My install of iATKOS for Youtube
My install of iATKOS (Part 1) - Click here for the video
Step 1) Go to start, and type in 'Run', and click enter.
Step 2) Now type in 'Compmgmt.msc', and click enter.
Step 3) Now click on 'Disk management', on the left hand side.
Step 4) Now right click on the partition you want to shrink, and click 'Shrink volume'.
Step 5) Now type in '15000', as in Mb's (15Gb), and click shrink.
Step 6) Now right click on the unnalocated space, and click on 'New simple volume'.
Step 7) Click 'Next', and 'Next' again, and 'Next' again.
Step 8) Now type in a name for your partition, and tick 'Perform quick format', and click 'Next', then click 'Finish'.
Step 9) Now go to start, click on the arrow next the the shutdown button, and click on 'Restart'.
Step 10) Get your iATKOS dvd ready, and put it in your dvd drive.
Step 11) Now when the countdown comes up, press 'F8', then type in '-v', and click enter.
Step 12) Now click on the arrow button '-->', and wait for it to prepare the installation.
My install of iATKOS (Part 2) - Click here for the video
Step 13) Now go to the top, and click on Utilities --> Disk Utility.
Step 14) Now click on the partition you just created, on the left.
Step 15) Then click on the erase tab, in the middle.
Step 16) Change it from 'MS-DOS (FAT)', to 'Mac OS Extended (Journaled)'.
Step 17) Now type in a name for the Mac partition.
Step 18) Then click on 'Erase', and 'Erase' again.
Step 19) Once finished, close Disk Utility.
Step 20) Now go to Utilities --> Darwin Boot.
Step 21) Now type in 'Y'.
Step 22) Then type in your hard drive number '1'.
Step 23) Then type in your Mac partition number '2'.
Step 24) Now type in 'Y', and 'Y' again.
Step 25) Now close Darwin Boot, and quit Terminal.
Step 26) Now click on 'Continue', then click on 'Agree'.
Step 27) Then click on the hard drive that pops up, and click on 'Continue'.
Step 28) Now click on 'Customize'.
Step 29) Now drop down 'Additional Patches', and tick 'EFI emulation'.
Step 30) Now drop down 'Drivers', and drop down 'System', and tick 'AppleSMBios.Kext'.
DO NO CHOOSE ANY OF THE DRIVER'S THAT I CHOOSE NOW, THEY ARE ONLY FOR MY LAPTOP, BUT YOU CAN CHOOSE YOUR DRIVER'S IF THERE UP THERE.
Step 31) Now click on 'Done', and then click on 'Install'.
Step 32) Now i will pop up with a message saying 'Check installation dvd', click on 'Skip', to save a lot of time.
Step 33) After it has finished, click on 'Restart', and boot from the dvd again.
Step 34) Once booted up, go to Utilities --> Terminal.
Step 35) Now type in 'fdisk -e /dev/rdisk0', and click enter.
Step 36) Now type in 'flag 2', and click enter.
Step 37) Now type in 'Update', and click enter.
Step 38) Now type in 'Write', and click enter. It will say 'Device could not be accessed exclusively', so type in 'Y', and click enter.
Step 39) Now type in 'Q', and click enter, to quit.
Step 40) Now close the Terminal window, and quit Terminal.
Step 41) Now quit the 'Mac OS X installer', and click on 'Restart'.
Step 42) Once it has restarted, take out the disc, and boot into Mac.
FOR SOME PEOPLE, IT WILL COME UP WITH THE MAC OS X LEOPARD WELCOME VIDEO, FOR SOME IT WONT COME UP, BUT DONT WORRY ABOUT THAT.
My install of iATKOS (Part 3) - Click here for the video
Step 43) As you can see, mine didn't come up with the welcome video, sometimes it comes up with it, sometimes it doesn't.
Step 44) Now choose your language, and click on 'Continue'.
Step 45) Now choose your keyboard layout, and click on 'Continue'.
Step 46) Now choose 'No do no.............', and click on 'Continue'.
NOW IT COMES UP WITH THE ENDLESS LOOP, IT MAY NOT HAPPEN TO SOME PEOPLE, BUT IT HAS HAPPENED WITH ME =[.
.........BUT THERE IS A SOLUTION FOR THIS, SO CARRY ON WATCHING, AND YOU'LL FIND OUT.
DID YOU SEE THAT!, IT WENT, AND NOW IT'S GOING TO COME BACK TO THE WELCOME SCREEN AGAIN.
FUCK THIS......... I'M TURNING YOU OFF BITCH.
Step 47) Once powered off, turn it back on.
Step 48) Press 'F8', and type in '-s', and click enter.
YOU WILL NOW SEE A LOT OF WRITING, DONT WORRY, IT IS LOADING SYSTEM FILES.
Step 49) When it has finished, type in '/sbin/mount -uw /', and click enter.
Step 50) Now type in 'Passwd root', and click enter.
IT WILL NOW ASK YOU TO TYPE IN A NEW PASSWORD, YOU MAY THINK THAT YOUR KEYBOARD HAS FROZEN, BUT IT HASN'T, IT JUST DOES.........
.....THIS FOR SECURITY, SO NO-ONE CAN SEE WHAT YOUR TYPING, SO BE CAREFUL WHAT YOU TYPE IN.
Step 51) Now it says to re-enter your password, to confirm it, so re-enter your password, and click enter.
Step 52) Now type in 'touch /var/db/.applesetupdone', and click enter.
Step 53) Now type in 'Reboot', to restart your computer.
Step 54) Now on the countdown, click enter, then click enter again, to boot up into Mac.
WOOOOOOOOOOOOOOOOOOO!, WERE NEARLY THERE!
Step 55) Now type in 'Root', for the username, and then type in your password, that you just created.
WOOPS, I TYPED IT IN WRONG LOL.
Step 56) Click on 'Login', to login, and there you are!, Mac OS X Leopard on a PC!