Achreon

sorry no copy and paste is allowed on this page

if you would like copies of info you can e-mail me

Here is a mixture for great smoke  bombs 4 parts of sugar to 6 parts

potassium nitrate (salt peter).  Heat  over low flame until it melts, stir

well. pour it into future container.   before it solidifes, imbed a few

matches as fuses into the mixture.   One lb. fills a block nicely with thick

white smoke.

take one CO2 cardige and empty it

use a nail to widen the hole in the top

fill the empty tank wiht gun powder

run a fuse into the hole

 

now fill tape shut the bottom a a cardboard tube and fill it with powdered aluminum

place the CO2 canister in the tube with the aluminum and tape sut leaving fuse exposed

put it somewhere out in the open, light it and run for your life

it will definetly kill anything within a 5 foot radius

if you think thats bead then whatch it go off its so cool 

what you need:

Iron oxide powder( can purchase at the store)

Pure Aluminum Powder

you mix these two ingredients in equal amounts. let sit for 24 hours to make a chemical bond. then light with a magnesium ribbon. this powerful stuff will burn at 6,000 degrees ferinhight. this you can use for many things like making glass from sand or anilating any thing you want like a police car. have fun!

what you need:

1 box of stirofoam packing peanuts

1 jar of gasoline

first you grab the jar of gasoline and put in a well ventelated area. then disolve as many packing peanuts as you can. Remeber that this will take a lot of packing peanust. after the gasoline will not disolve any more, you then let it ferment for 2 hour. then it is ready to use. Be Careful and have fun!

• oleic acid (may be found in some pharmacies, craft, and health food stores)
• household ammonia
• PCB etchant (ferric chloride solution) - may be found at Radio shack
• distilled water
• steel wool
• a strong magnet
• kerosene
• heat source
• 2 Pyrex beakers or measuring cups
• a plastic syringe
• coffee filters

The first step is to prepare the magnetite, which will be the source of the magnetic particles in the Ferro fluid. First reduce ferric chloride (FeCl₃) in PCB etchant to ferrous chloride (FeCl₂), which will be used to make magnetite. Commercial PCB etchant is usually 1.5M ferric chloride, to yield 5 grams of magnetite.

1. Use the plastic syringe to measure and dispense 10 ml of PCB etchant into a Pyrex measuring cup. Add 10 ml of distilled water. The etchant is diluted with water because there is an additive in Radio shack PCB fluid that can cause side reactions with the iron.
2. Drop a small piece of steel wool into the diluted etchant solution. Stir or swirl the liquid around until it turns bright green (this is the FeCl₂).
3. Filter the liquid through a coffee filter to remove the particulate contaminants.

Next, magnetite will be precipitated from the ferrous and ferric chloride solutions. Add 20 ml of PCB etchant (FeCl₃) to the green solution (FeCl₂). FeCl₃ and FeCl₂ react in a 2:1 ratio. The concentration of the FeCl₂ just prepared is half that of the FeCl₃ (because the water was added), so equal volumes will give the desired ratio.

4. Add 150 ml of household ammonia, stirring continuously. The ammonia reacts with the iron salts and excess chlorine to produce the magnetite, Fe₃O₄, which falls out of solution, in an ammonium chloride solution.

The next step is to take the magnetite and suspend it in the carrier solution.

Next, the magnetic particles need to be coated with a surfactant, so that they won't stick together, even in a magnetic field, and suspended in a carrier, so the magnet will be fluid.

1. Coat the magnetite particles with oleic acid by heating the solution to just below boiling, in a well-ventilated area or under a fume hood. Stir in 5 ml of oleic acid. Keep the liquid near boiling until the odor of ammonia disappears (approximately one hour). Remove the mixture from heat and allow it to cool to room temperature. The oleic acids reacts with ammonia to form ammonium oleate. Heat causes the ammonium oleate to break down, allowing the oleate ion to enter into solution, while the ammonia escapes as a gas. The oleate ion attaches to a magnetite particle and is reconverted to oleic acid.
2. The coated magnetite is suspended in the kerosene carrier by adding 100 ml of kerosene to the coated magnetite suspension, again, in a well-ventilated area.

Stir the suspension until most of the black coloration has left the water and has been transferred into the kerosene. Magnetite and oleic acid are insoluble in water, while oleic acid is soluble in kerosene. Stirring the mixure allows the coated particles to leave the aqueous phase in favor of the kerosene.

3. Decant and save the kerosene layer. Discard the water. The magnetite plus oleic acid plus kerosene is the final product, the ferrofluid.

                                                                      

You will need 3 chemicals to make Black Powder, they are: Potassium Nitrate, Sulfur and Charcoal. Stay away from very low grade materials like "Dusting Sulfur" and Bar-B-Que Charcoal Briquettes. The Charcoal you use in a BBQ is not pure Charcoal. It contains other materials and chemicals that are designed to keep the material burning evenly and for a long time, but it will make lousy Black Powder. If you use low quality chemicals, you will undoubtedly get low quality Black Powder.
  The following is the standard formula for Black Powder:

silver nitrate is used  for making flash powder and light sensitive silver paper.

what you need:

2 oz. fine silver

2 cups white fuming nitric acid

 

first dissolve the silver in the acid. this will take anywhere from hours to days depending on how strong the acid is. then evaporate the rest of the remaning liquid. this will leave you with granulated silver nitrate.

dragons breath is a highly flamible substance.

what you need:

2 cups lycopodium powder.( lycopodium is a plant which grows just about anywhere. you can dry it and powder it with a mortar and pestle. it must be really fine though.) 

1/2 cup gasoline

just mix these two ingredience and then let fully dry in the sun. this can easly catch fire so be carful. be creative!

"Negative X"